About S5 Inserter

• Extra tall adjustable-height scleral lens insertion stand
• Embedded rechargeable light
• Base suctions to countertop
• For use with DMV Vented Scleral Cup (1 included)
  
• Stand height: 10" extending to 29.5". Base is 2 3/8" diameter.
• Kit includes: Stand with light; DMV Vented Scleral Cup; USB/USB-C charging kit; QR code for manual; rigid travel case (5.5" x 8.75" x 2.75")

Description (Rebecca's)

I have only recently interacted with people who are using this tool, so while i've known about the S5 products for a long time, I'm not yet very experienced with identifying which people benefit the most. I am looking forward to hearing from more users. If you try it, please make sure to either post a review or send me your thoughts so I can continue to adapt my description to be as helpful as possible.

The big picture

The most important things to know about this product:

1. This is THE scleral lens insertion stand for tall people.
2. The light is very bright.
3. The base suctions to the counter. 
4. It comes with support.

This is not a product that people buy "just because" or "just in case". This is the product you purchase when standard methods aren't working AND/OR when you need as much extra support as possible.

Dr Mahgoub

The S5 and S5 Mini are designed and sold by Dr. Fayiz Mahgoub. Dr. Mahgoub is doing a lot of good work educating his colleagues about the need for assistive technologies for lens handling. Part of the package when you purchase this product is support for your learning process, so if you are struggling a lot with lens insertion I encourage you to reach out to him. Product and warranty support are all exceptional.

The light

There is an orange/yellow light embedded in the stand. It is very bright and for me, uncomfortably so. Do not make the mistake I did, which was to turn it on before I had added the plunger. Even then, when it's new, personally I find it much too bright. However, I have learned from long-time users of this product that not only does it dim somewhat over time compared to when it's new, but there are also people who like it this bright. 

The stand

As you can see in the pic, it's starts with a suction cup, then a durable attachment point, a telescoping thing like a radio antenna, and finally the stand proper, that is, a 4" black thing containing the light and power source plus the orange extension where the scleral cup is placed.

My first step after securing the suction cup to the counter would be to lay a terry towel all round to make sure there's a soft landing. I am a bit paranoid about tall stands, having tested some interesting prototypes from other designers over the years. (I'm always thinking, will my lens fall off and crack?  Hence the towel.)

I prefer putting my lenses in standing up rather than seated, so if I actually needed a stand, I'd consider this for myself to use at work. When attached to my desk, I can extend it to 22" and then it's the perfect height for me. The full extended height is almost 30", so it should be OK for the tallest people if they attach it to something counter-height rather than desk-height.

Otherwise, it performs the same function as other stands, as in, the purpose is to hold the lens in a plunger so that you can bring your eye to the lens rather than bringing the lens to your eye.

Description (Manufacturer's)

Click here to download the user manual for the S5 Inserter (or see copy below)

About

The S5 Inserter was developed by Dr. Fayiz Mahgoub to eliminate the challenges that his patients experienced with inserting their scleral and hybrid lenses. Its features include

Unmatched Support

• Comes with unlimited access to 1 on 1 coaching with Dr. Mahgoub. Available 7 days a week via phone, text, email and video chat/FaceTime.
• Includes a detailed user manual with instructions and tips to help make your lens insertion experience as safe and efficient as possible (via website/qr code - no paper manual included)
• Includes a 1 year manufacturer warranty that covers parts, labor and shipping within the Unites States.
• Comes with a 90-day money back guarantee to give you peace of mind as you learn the insert your lenses. 

Hands-free lens stabilization:

• Gives the user two free hands to hold their eyelids open which helps counter the human blink reflex.
• Helps reduce spilling of the contact lens solution which decreases the chance of air bubbles getting trapped under the lens. 

LED light source:

• Enables the user to more easily align their eye with the center of the lens during insertion.

Adjustable height:

• Allows the user to position the lens at the most comfortable height for insertion.
• The height from the base of the device to the top of the lens holder can be adjust from 10.5 inches (27 cm) to 2 ft 6 inches (76 cm).
• Optimized for lens insertion while standing.

S5 Inserter User Manual

Safety precautions (Please read before use)

1. Please consult with your eyecare provider for instructions on how to clean and maintain your lenses. Your doctor will recommend the appropriate lens cleaning and maintenance products that you should use with your lenses. 
2. If you experience pain or a decrease in the quality of your vision after using the S5 Inserter stop using the device and contact your eyecare provider immediately.
3. Lens Holder: 
   1. Please read the insert provided with the lens holder before using it.
   2. ALLERGY NOTICE: The lens holder provided with the S5 Inserter (known as the DMV Vented Scleral Cup) contains latex. 
   3. The lens holder provided with the S5 Inserter is only intended for use in lens insertion. Do not use the provided lens holder during lens removal.
   4. CHOKING HAZARD: Please keep the lens holder out of reach of the children. 

Warranty Information

Your S5 Inserter Comes with a 1-year warranty which covers the replacement of any components that fail to operate due to manufacturer defect. Register your device at https://augmentedvisionlabs.com/warranty/

Device Maintenance

1. Please clean the rubber lens holder with an alcohol wipe before every use and allow it to dry completely before placing a lens on it. The lens holder should be replaced at least once every 3 months.
2. Immediately after inserting your lenses, please take a moment to remove any liquid that may have spilled onto your device. Do not discconect the light unit from the telescoping arm until after you have dried the outside of the light unit with a paper towel. This will help prevent water from getting into the electronic components of your device. 
3. Please make sure that the storage case for your device is completely dry before storing the device in it. If you store containers that hold liquids (ex. contact lens cases) in your case, please ensure that they are securely closed to prevent liquid damage to your device.
   1. We recommend cleaning the outside of your device as well as the inside of your storage case at least once per week with alcohol wipes. After cleaning, make sure that all parts are completely dry before storing them.
4. The bottom of the suction base should be cleaned periodically with an alcohol wipe to ensure maximum suction. 
5. Charging the light unit:
   1. When you notice the light becoming dim, its time to charge the light unit. 
      1. Locate the USB port on the bottom of the light unit.
      2. Connect the female end of the provided USB extension cable to the bottom of the light unit. 
      3. Connect the male end of the cable to a desktop or laptop computer. 
   2. The light unit will reach a full charge after 1 hour of being plugged in.

Instructions for use

Before lens insertion

1. Place the suction base on a smooth, flat surface. Ensure that both the bottom of the suction base and the surface are clean and dry. 
2. Hold down the outer edge of the suction base while pulling metal telescoping arm upward until it locks into place in the vertical position. This will engage the suction of the base. 
3. Once the telescoping arm is in the vertical position, slide the base of the arm forward for increased stability.
4. Extend the telescoping arm to the desired height.
   1. We recommend that you keep the height as low as possible when you are first learning to use the device to reduce the chance of your lens being accidentally bumped off the lens holder and falling from a high distance. This could cause the lens to become lost or damaged. When you become confident in your ability to consistently insert the lens without it falling, you can increase the height to your preferred height for lens insertion. 
5. Screw the light unit into the light unit dock.
6. Insert the rubber lens holder into the orange lens holder dock.
7. Wash your hands with a scent-free, moisturizer-free soap for 20 second and dry them with a lint-free towel.
8. Clean the rubber lens holder with a disinfecting alcohol wipe. 
   1. Allow the lens holder to dry completely before placing your contact lens on it. 
9. Clean the upper segment of the light unit (the part that twists) with a disinfecting alcohol wipe. 
   1. You can use the same wipe that you previously used to clean the lens holder. 
10. Twist the top half of the light unit counterclockwise to activate the light.
11. Inspect your lens to make sure it is clean and free of damage then place it on the rubber lens holder. 
    1. It is recommended to rinse your lens with preservative free saline if it was previously stored in a multi-purpose cleaning solution.
    2. If your lens has a black dot that is used for positioning your lens, please make sure that the dot is placed at the position recommended by your doctor (example: place the black dot at the 6 o'clock position). 
12. Fill the lens bowl with a preservative-free saline solution that is approved by your doctor.
    1. Add the saline until the level rises above the edge of the lens.

Lens insertion

1. Place your head directly over the lens, making sure that your head is level with the survace that your device was placed on. Your chin should be tucked in toward your chest. 
2. Use both hands to firmly hold your upper and lower eyelids open. 
   1. Tip #1: Place your fingers as close as possible to your eyelashes (without touching your eyelashes) to get the best grip on your eyelids.
   2. Tip #2: Pull your upper lid upward and pin it against your brow bone by pressing your finger in towards your face. Pull your lower lid down and pin it against your cheek bone by pressing your finger in towards your face. 
3. Keep both eyes open and slowly move your head down toward the lens until your eye makes contact with the lens. 
   1. Tip #1: Focus on the light as you move closer to the lens. The light will look perfectly round if you are lined up with the center of the lens. If the light does not look round, you will need to adjust the position of your head until it becomes round. 
   2. Tip #2: The first thing you will feel is your eye touching the saline solution. Do not slow down when you feel the saline. Keep going at the same pace until you feel the pressure of the lens being pressed against your eye. It is normal for saline to spill out of the lens bowl during this process.
4. Once you feel the pressure of the lens being pressed onto your eye, move your head up and away from the device and slowly release your eyelids. 
5. Twist the top half of the light unit clockwise to turn the light off. 
6. For your second eye: 
   1. Repeat steps 10 through 12 in the "Before Lens Insertion" section to prepare your second lens for insertion
   2. Repeat steps 1 through 5 in the "Lens Insertion" section to insert your second lens. 
7. After inserting your lenses, please take a moment to check for air bubbles. 
   1. Cover one eye at a time to see if you can notice any air bubbles in your line of sight.
   2. You can also use the mirror to inspect the lens on your eye and check for air bubbles. Shining a flashlight on your face will help provide better lighting.
   3. If air bubbles are present, you must remove the lens and re-insert it.

After Lens Insertion

1. Remove the rubber lens holder from the light unit.
2. Keep the light unit connected to the telescoping arm and dry off the outside of the light unit with a paper towel. 
3. Disconnect the light unit from the telescoping arm.
4. Additional drying for the light unit:
   1. Turn the light unit upside down to get rid of any liquid that has built up inside the orange lens holder dock. Use a paper towel or a q-tip to soak up any liquid remaining in the lens holder dock after draining. 
   2. If you see liquid on or near the USB port of the light unit, soak it up with a paper towel or q-tip. If there is no liquid on the USB port, then please avoid touching it. 
5. Detach the base:
   1. Collapse the telescoping arm down to its shortest height.
   2. Push the telescoping arm to the horizontal position to break the suction of the base. 
      1. If the suction doesn't release right away, it may be necessary to use a fingernail or a plastic card to separate the edge of the base from the surface that it is suctioned to.
6. Drying the telescoping arm and base:
   1. Turn the telescoping arm upside down and shake well to remove any liquid that is trapped between the segments. 
   2. Extend the telescoping arm to its full length and use a dry paper towel to remove all remaining moisture on the telescoping arm and the suction base. 
7. Please ensure that the storage case used to store the device is completely dry before using it to store your device. This is important for reducing the growth of microbes in the storage case as well as reducing the chance of moisture causing damage to the electronics of your device. 
   1. It is recommended that you use alcohol or another disinfecting solution to clean the inside and outside of your storage case at least once per week. After cleaning, make sure that the case dries completely before using it to store your device and lens accessories.